Plumbing for Beginners: The Essentials for Bathtub Installation
Plumbing for Beginners: The Essentials for Bathtub Installation
Blog Article
What're your concepts on Installing A Bathtub?
Mounting a tub isn't specifically rocket science, but it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is additionally a moderately hard project. If the old bathtub is conveniently easily accessible, the job can move quickly; if you need to open up a wall to get rid of the old bathtub and also place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly need a helper to leave the old tub and also set in the brand-new one. Make certain you have certified on your own for the work and fit trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to consider employing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This article will help you mount a new tub in your shower room if you have currently gotten a brand-new tub as well as don't require to alter the plan of your previous water pipes.
Your devices and also material checklist need to comprise the following:
Planning for the Installment
To start with, the sustaining frame provided with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its final position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the limited gain access to that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level checks out level.
To mount taps, fit all-time low of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and examine all joints and brand-new pipework for leaks and tighten them if needed. Fill the bathtub and likewise check the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's user's manual. Tiling as well as sealing around the bathtub must wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washers remain in place between the faucet as well as the sink. Safeguard the faucet in place with the maker given backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind should be linked to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to break a rigid seal, causing the water to penetrate the wall surface between the bath and the tiling, causing issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to enable the movement experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not think about this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily readily available on the marketplace. It is advisable to fit the tiles using waterproof or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog posting on How to Install a Bathtub when perusing the search engines. Liked our review? Please share it. Let others discover it. Thanks so much for taking the time to read it.
Professional touch? Contact. Report this page